Manufacturing · Shelby Township, MI
Xcentric Mold & Engineering LLC
According to OSHA enforcement records (2010–2026), Xcentric Mold & Engineering LLC has a relatively clean safety record: 2 violations across 2 inspections. See the full breakdown below.
- $0
- OSHA penalties
- 2
- Violations cited
- 2
- OSHA inspections
Xcentric Mold & Engineering LLC in Shelby Township, MI has been the subject of 2 OSHA workplace inspections and 2 citations since 2010, according to enforcement records from the U.S. Department of Labor. All enforcement data below is sourced from the DOL public enforcement databases at data.dol.gov.
The record in one line
OSHA has inspected Xcentric Mold & Engineering LLC 2 times over 1 year - more than twice a year on average. These inspections resulted in 2 violations, averaging 1.0 per inspection. Against the Manufacturing industry average of 3 inspections per employer, this runs moderately below peers (0.8x the sector average) on inspection frequency. For comparison, Truss Craft of Nebraska in Grand Island, NE is another manufacturing employer with 2 OSHA inspections on record and $0 in current penalties.
- 1.0
- violations per inspection
- 0.0%
- of violations were serious
Compliance score
- C OSHA safety compliance: 2 violations across 2 OSHA inspections (1.0 per inspection), vs. national p10 0.0 (best) / p90 5.5 (worst) among 145,626 inspected employers.
Channels are separate federal datasets: a dimension marked not applicable simply has no record in that dataset for this employer, not a good or bad score.
Does more inspection scrutiny mean more findings?
Each dot is one of 21 Manufacturing employers with an OSHA inspection on record, placed by inspections and violations cited. The highlighted dot is Xcentric Mold & Engineering LLC.
How Xcentric Mold & Engineering LLC Compares
Xcentric Mold & Engineering LLC's 1.00 violations per inspection compares to the Manufacturing sector average of 8.0 violations per employer.
No OSHA penalty has been assessed against Xcentric Mold & Engineering LLC to date. The Manufacturing sector average runs $15,763 per employer.
Enforcement detail
OSHA Inspection History
Total Inspections
2
First Inspection
2020-11-24
Last Inspection
2020-11-24
Inspection Span
1 yr
Violations / Inspection
1.0
Avg Penalty / Inspection
$0
Industry Avg / Inspection
$6,093
What this shows 2 inspections over 1 year, averaging 1.0 violations per visit. That's $0 per inspection vs. the Manufacturing average of $6,093.
Enforcement detail
Violation Breakdown
0
Serious
0.0% of total
0
Willful
0.0% of total
0
Repeat
0.0% of total
2
Other-Than-Serious
100.0% of total
What this shows Serious violations involve hazards that could cause death or serious physical harm. Willful violations indicate intentional or knowing disregard of the law. Repeat violations are for hazards previously cited within the past 5 years.
Industry Safety Context: Manufacturing
How Xcentric Mold & Engineering LLC compares to the Manufacturing sector, which has 44,645 employers tracked by PlainWorker.
| Metric | Xcentric Mold & Engineering LLC | Industry Avg |
|---|---|---|
| Inspections | 2 | 2.6 |
| Violations | 2 | 8.0 |
| Total Penalty | $0 | $15,763 |
| Avg Penalty per Inspection | $0 | $6,093 |
Nationwide Manufacturing peers with similar penalties or inspection counts
Two OSHA-record peer sets for Xcentric Mold & Engineering LLC, both outside MI so the neighborhoods are not geographic containment.
Similar OSHA inspection count
Same-sector employers with a comparable inspection history outside this state (2 inspections here).
Nearby & Similar Employers in Manufacturing
Showing 5 of 44644 other employers tracked in this sector.
Compare Xcentric Mold & Engineering LLC vs Chep Services, LLC side-by-side →
What to do with this record
Use Xcentric Mold & Engineering LLC's enforcement history as one data point, not the whole picture.
- A single employer's record can look unusual in isolation. Compare Xcentric Mold & Engineering LLC against Chep Services, LLC, a similarly-sized employer in the same sector, before drawing conclusions. Compare side-by-side
- See whether Xcentric Mold & Engineering LLC's inspection and penalty record is typical for Manufacturing or an outlier against the sector's own average. View the Manufacturing sector
- Before you accept a job or raise a safety concern, search any employer for its own OSHA inspection history the same way you found this one. Search employers
Figures reflect closed OSHA and WHD federal enforcement actions on record (2010–2026); not every workplace issue results in an inspection or investigation.
Frequently Asked Questions
Is Xcentric Mold & Engineering LLC safe to work at? ▼
How many OSHA violations does Xcentric Mold & Engineering LLC have? ▼
How many OSHA inspections has Xcentric Mold & Engineering LLC had? ▼
What is the total penalty amount for Xcentric Mold & Engineering LLC? ▼
What industry does Xcentric Mold & Engineering LLC operate in? ▼
How does Xcentric Mold & Engineering LLC's safety record compare to industry average? ▼
Data Sources & Methodology ▼
Data as of 2026. Source: U.S. Department of Labor (OSHA, WHD).
Source: OSHA Enforcement Data
Inspection and violation records from the Occupational Safety and Health Administration (OSHA), U.S. Department of Labor, covering the period 2010–2026. Includes inspection dates, violation types (serious, willful, repeat, other-than-serious), and penalty amounts. Penalties shown are current assessed amounts and may differ from original citations due to settlement, contest, or reduction.
Source: Wage and Hour Division (WHD)
Compliance actions from the WHD, covering enforcement of the Fair Labor Standards Act (FLSA), including minimum wage, overtime, and child labor violations. Back wages represent amounts owed to affected employees as determined by WHD investigations.
Employer Matching
Employers are matched across OSHA and WHD datasets by name, state, and city. Employers included in PlainWorker have 2 or more OSHA inspections or $1,000+ in WHD back wages. Data is updated monthly from data.dol.gov.