Transportation & Warehousing · Brooklyn, NY
Mta NYCT Inf Stationary Engineering
According to OSHA enforcement records (2010–2026), Mta NYCT Inf Stationary Engineering has a concerning safety record: 8 violations across 2 inspections. See the full breakdown below.
- $0
- OSHA penalties
- 8
- Violations cited
- 2
- OSHA inspections
Mta NYCT Inf Stationary Engineering in Brooklyn, NY has been the subject of 2 OSHA workplace inspections and 8 citations since 2010, according to enforcement records from the U.S. Department of Labor. All enforcement data below is sourced from the DOL public enforcement databases at data.dol.gov.
The record in one line
OSHA has inspected Mta NYCT Inf Stationary Engineering 2 times over 2 years, roughly annually. These inspections resulted in 8 violations, averaging 4.0 per inspection, above what's typical for a single visit. Of these, 6 were classified as serious - indicating hazards that could cause death or serious harm. Against the Transportation & Warehousing industry average of 2 inspections per employer, this sits roughly in line with peers (1.1x the sector average) on inspection frequency. For comparison, Tupper Lake CSD Bus Garage in Tupper Lake, NY is another transportation & warehousing employer with 2 OSHA inspections on record and $0 in current penalties.
- 4.0
- violations per inspection
- 75.0%
- of violations were serious
Compliance score
- F OSHA safety compliance: 8 violations across 2 OSHA inspections (4.0 per inspection), vs. national p10 0.0 (best) / p90 5.5 (worst) among 145,626 inspected employers.
Channels are separate federal datasets: a dimension marked not applicable simply has no record in that dataset for this employer, not a good or bad score.
Does more inspection scrutiny mean more findings?
Each dot is one of 21 Transportation & Warehousing employers with an OSHA inspection on record, placed by inspections and violations cited. The highlighted dot is Mta NYCT Inf Stationary Engineering.
How Mta NYCT Inf Stationary Engineering Compares
Mta NYCT Inf Stationary Engineering's 4.00 violations per inspection compares to the Transportation & Warehousing sector average of 3.2 violations per employer.
No OSHA penalty has been assessed against Mta NYCT Inf Stationary Engineering to date. The Transportation & Warehousing sector average runs $6,129 per employer.
Enforcement detail
OSHA Inspection History
Total Inspections
2
First Inspection
2014-01-31
Last Inspection
2015-08-28
Inspection Span
2 yrs
Violations / Inspection
4.0
Avg Penalty / Inspection
$0
Industry Avg / Inspection
$3,295
What this shows 2 inspections over 2 years, averaging 4.0 violations per visit. That's $0 per inspection vs. the Transportation & Warehousing average of $3,295.
Enforcement detail
Violation Breakdown
6
Serious
75.0% of total
0
Willful
0.0% of total
0
Repeat
0.0% of total
2
Other-Than-Serious
25.0% of total
What this shows Serious violations involve hazards that could cause death or serious physical harm. Willful violations indicate intentional or knowing disregard of the law. Repeat violations are for hazards previously cited within the past 5 years.
Industry Safety Context: Transportation & Warehousing
How Mta NYCT Inf Stationary Engineering compares to the Transportation & Warehousing sector, which has 9,914 employers tracked by PlainWorker.
| Metric | Mta NYCT Inf Stationary Engineering | Industry Avg |
|---|---|---|
| Inspections | 2 | 1.9 |
| Violations | 8 | 3.2 |
| Total Penalty | $0 | $6,129 |
| Avg Penalty per Inspection | $0 | $3,295 |
Nationwide Transportation & Warehousing peers with similar penalties or inspection counts
Two OSHA-record peer sets for Mta NYCT Inf Stationary Engineering, both outside NY so the neighborhoods are not geographic containment.
Similar OSHA inspection count
Same-sector employers with a comparable inspection history outside this state (2 inspections here).
Nearby & Similar Employers in Transportation & Warehousing
Showing 5 of 9913 other employers tracked in this sector.
Compare Mta NYCT Inf Stationary Engineering vs Agi LLC- Lga Ground side-by-side →
What to do with this record
Use Mta NYCT Inf Stationary Engineering's enforcement history as one data point, not the whole picture.
- A single employer's record can look unusual in isolation. Compare Mta NYCT Inf Stationary Engineering against Agi LLC- Lga Ground, a similarly-sized employer in the same sector, before drawing conclusions. Compare side-by-side
- See whether Mta NYCT Inf Stationary Engineering's inspection and penalty record is typical for Transportation & Warehousing or an outlier against the sector's own average. View the Transportation & Warehousing sector
- Before you accept a job or raise a safety concern, search any employer for its own OSHA inspection history the same way you found this one. Search employers
Figures reflect closed OSHA and WHD federal enforcement actions on record (2010–2026); not every workplace issue results in an inspection or investigation.
Frequently Asked Questions
Is Mta NYCT Inf Stationary Engineering safe to work at? ▼
How many OSHA violations does Mta NYCT Inf Stationary Engineering have? ▼
How many OSHA inspections has Mta NYCT Inf Stationary Engineering had? ▼
What is the total penalty amount for Mta NYCT Inf Stationary Engineering? ▼
Does Mta NYCT Inf Stationary Engineering have any serious or willful violations? ▼
What industry does Mta NYCT Inf Stationary Engineering operate in? ▼
How does Mta NYCT Inf Stationary Engineering's safety record compare to industry average? ▼
Data Sources & Methodology ▼
Data as of 2026. Source: U.S. Department of Labor (OSHA, WHD).
Source: OSHA Enforcement Data
Inspection and violation records from the Occupational Safety and Health Administration (OSHA), U.S. Department of Labor, covering the period 2010–2026. Includes inspection dates, violation types (serious, willful, repeat, other-than-serious), and penalty amounts. Penalties shown are current assessed amounts and may differ from original citations due to settlement, contest, or reduction.
Source: Wage and Hour Division (WHD)
Compliance actions from the WHD, covering enforcement of the Fair Labor Standards Act (FLSA), including minimum wage, overtime, and child labor violations. Back wages represent amounts owed to affected employees as determined by WHD investigations.
Employer Matching
Employers are matched across OSHA and WHD datasets by name, state, and city. Employers included in PlainWorker have 2 or more OSHA inspections or $1,000+ in WHD back wages. Data is updated monthly from data.dol.gov.