Manufacturing · Carol Stream, IL
Metals Technology Corporation
According to OSHA enforcement records (2010–2026), Metals Technology Corporation has a relatively clean safety record: 1 violations across 4 inspections. See the full breakdown below.
- $0
- OSHA penalties
- 1
- Violations cited
- 4
- OSHA inspections
Metals Technology Corporation in Carol Stream, IL has been the subject of 4 OSHA workplace inspections and 1 citations since 2010, according to enforcement records from the U.S. Department of Labor. All enforcement data below is sourced from the DOL public enforcement databases at data.dol.gov.
The record in one line
OSHA has inspected Metals Technology Corporation 4 times over 5 years, roughly once every couple of years. These inspections resulted in just 1 violation, averaging 0.3 per inspection - fewer than typical. Against the Manufacturing industry average of 3 inspections per employer, this runs moderately above peers (1.5x the sector average) on inspection frequency. For comparison, Richard & Sons, LLC in Fond Du Lac, WI is another manufacturing employer with 2 OSHA inspections on record and $0 in current penalties.
- 0.3
- violations per inspection
- 0.0%
- of violations were serious
Compliance score
- B OSHA safety compliance: 1 violation across 4 OSHA inspections (0.3 per inspection), vs. national p10 0.0 (best) / p90 5.5 (worst) among 145,626 inspected employers.
Channels are separate federal datasets: a dimension marked not applicable simply has no record in that dataset for this employer, not a good or bad score.
Does more inspection scrutiny mean more findings?
Each dot is one of 21 Manufacturing employers with an OSHA inspection on record, placed by inspections and violations cited. The highlighted dot is Metals Technology Corporation.
How Metals Technology Corporation Compares
Metals Technology Corporation's 0.25 violations per inspection compares to the Manufacturing sector average of 8.0 violations per employer.
No OSHA penalty has been assessed against Metals Technology Corporation to date. The Manufacturing sector average runs $15,763 per employer.
Enforcement detail
OSHA Inspection History
Total Inspections
4
First Inspection
2010-10-07
Last Inspection
2016-02-16
Inspection Span
5 yrs
Violations / Inspection
0.3
Avg Penalty / Inspection
$0
Industry Avg / Inspection
$6,093
What this shows 4 inspections over 5 years, averaging 0.3 violations per visit. That's $0 per inspection vs. the Manufacturing average of $6,093.
Enforcement detail
Violation Breakdown
0
Serious
0.0% of total
0
Willful
0.0% of total
0
Repeat
0.0% of total
1
Other-Than-Serious
100.0% of total
What this shows Serious violations involve hazards that could cause death or serious physical harm. Willful violations indicate intentional or knowing disregard of the law. Repeat violations are for hazards previously cited within the past 5 years.
Industry Safety Context: Manufacturing
How Metals Technology Corporation compares to the Manufacturing sector, which has 44,645 employers tracked by PlainWorker.
| Metric | Metals Technology Corporation | Industry Avg |
|---|---|---|
| Inspections | 4 | 2.6 |
| Violations | 1 | 8.0 |
| Total Penalty | $0 | $15,763 |
| Avg Penalty per Inspection | $0 | $6,093 |
Nationwide Manufacturing peers with similar penalties or inspection counts
Two OSHA-record peer sets for Metals Technology Corporation, both outside IL so the neighborhoods are not geographic containment.
Similar OSHA inspection count
Same-sector employers with a comparable inspection history outside this state (4 inspections here).
Nearby & Similar Employers in Manufacturing
Showing 5 of 44644 other employers tracked in this sector.
Compare Metals Technology Corporation vs Commodore Plastics LLC side-by-side →
What to do with this record
Use Metals Technology Corporation's enforcement history as one data point, not the whole picture.
- A single employer's record can look unusual in isolation. Compare Metals Technology Corporation against Commodore Plastics LLC, a similarly-sized employer in the same sector, before drawing conclusions. Compare side-by-side
- See whether Metals Technology Corporation's inspection and penalty record is typical for Manufacturing or an outlier against the sector's own average. View the Manufacturing sector
- Before you accept a job or raise a safety concern, search any employer for its own OSHA inspection history the same way you found this one. Search employers
Figures reflect closed OSHA and WHD federal enforcement actions on record (2010–2026); not every workplace issue results in an inspection or investigation.
Frequently Asked Questions
Is Metals Technology Corporation safe to work at? ▼
How many OSHA violations does Metals Technology Corporation have? ▼
How many OSHA inspections has Metals Technology Corporation had? ▼
What is the total penalty amount for Metals Technology Corporation? ▼
What industry does Metals Technology Corporation operate in? ▼
How does Metals Technology Corporation's safety record compare to industry average? ▼
Data Sources & Methodology ▼
Data as of 2026. Source: U.S. Department of Labor (OSHA, WHD).
Source: OSHA Enforcement Data
Inspection and violation records from the Occupational Safety and Health Administration (OSHA), U.S. Department of Labor, covering the period 2010–2026. Includes inspection dates, violation types (serious, willful, repeat, other-than-serious), and penalty amounts. Penalties shown are current assessed amounts and may differ from original citations due to settlement, contest, or reduction.
Source: Wage and Hour Division (WHD)
Compliance actions from the WHD, covering enforcement of the Fair Labor Standards Act (FLSA), including minimum wage, overtime, and child labor violations. Back wages represent amounts owed to affected employees as determined by WHD investigations.
Employer Matching
Employers are matched across OSHA and WHD datasets by name, state, and city. Employers included in PlainWorker have 2 or more OSHA inspections or $1,000+ in WHD back wages. Data is updated monthly from data.dol.gov.