PlainWorker
Employers › GA

Manufacturing · Atlanta, GA

Halperns Steak and Seafood

According to OSHA enforcement records (2010–2026), Halperns Steak and Seafood ranks #72,865 of 99,447 penalized U.S. employers by total current penalty, with a relatively clean safety record: 1 violations across 2 inspections.

Lower half by penalty100% serious
$2,430
OSHA penalties
1
Violations cited
2
OSHA inspections
#72,865
of 99,447 penalized employers

Halperns Steak and Seafood in Atlanta, GA has been the subject of 2 OSHA workplace inspections and 1 citations since 2010, according to enforcement records from the U.S. Department of Labor. Total penalties assessed: $2,430. All enforcement data below is sourced from the DOL public enforcement databases at data.dol.gov.

The record in one line

OSHA has inspected Halperns Steak and Seafood 2 times over 3 years, roughly once every couple of years. These inspections resulted in 1 violation, averaging 0.5 per inspection, on the lighter side. According to OSHA enforcement records, its total current penalty ranks #72,865 of 99,447 penalized U.S. employers (the lower half of penalized employers nationally). Of these, 1 were classified as serious - indicating hazards that could cause death or serious harm. Against the Manufacturing industry average of 3 inspections per employer, this runs moderately below peers (0.8x the sector average) on inspection frequency. For comparison, Industrial Steel in Pearl, MS is another manufacturing employer with 2 OSHA inspections on record and $2,430 in current penalties.

0.5
violations per inspection
100.0%
of violations were serious
#72,865
of 99,447 penalized employers

Compliance score

B 83/100
  • B OSHA safety compliance: 1 violation across 2 OSHA inspections (0.5 per inspection), vs. national p10 0.0 (best) / p90 5.5 (worst) among 145,626 inspected employers.

Channels are separate federal datasets: a dimension marked not applicable simply has no record in that dataset for this employer, not a good or bad score.

Open my watchlist

How Halperns Steak and Seafood compares on OSHA penalties

Total current penalty vs the Manufacturing per-employer average

in penalties

What this shows Halperns Steak and Seafood runs well below peers (0.15x the sector average) in total OSHA penalties.

Source U.S. Department of Labor, OSHA enforcement extracts As of 2026

Where this penalty ranks nationally

Total current OSHA penalty vs every U.S. employer with a nonzero penalty

$2,430 Top 27% most affordable more affordable than 73% of 99,447 U.S. employers with a penalty

$0–$5,000: 43,959 U.S. employers with a penalty (44%). This entry sits in this band. $5,000–$10,000: 20,304 U.S. employers with a penalty (20%). Above this entry. $10,000–$15,000: 11,027 U.S. employers with a penalty (11%). Above this entry. $15,000–$20,000: 6,546 U.S. employers with a penalty (7%). Above this entry. $20,000–$25,000: 4,175 U.S. employers with a penalty (4%). Above this entry. $25,000–$30,000: 2,877 U.S. employers with a penalty (3%). Above this entry. $30,000–$35,000: 2,036 U.S. employers with a penalty (2%). Above this entry. $35,000–$40,000: 1,493 U.S. employers with a penalty (2%). Above this entry. $40,000–$45,000: 1,095 U.S. employers with a penalty (1%). Above this entry. $45,000–$50,000: 785 U.S. employers with a penalty (1%). Above this entry. $50,000–$55,000: 5,150 U.S. employers with a penalty (5%). Above this entry. This employer $0 $55,000 every penalized U.S. employer, bucketed by value

Each bar is a $5K-wide band; taller bars hold more U.S. employers with a penalty. The dashed line + filled bar mark this entry. Hover or tap any bar for its full count, share, and where it sits relative to this entry.

Source U.S. Department of Labor, OSHA enforcement extracts · 2026

Does more inspection scrutiny mean more findings?

Each dot is one of 21 Manufacturing employers with an OSHA inspection on record, placed by inspections and violations cited. The highlighted dot is Halperns Steak and Seafood.

Frequently inspected, many findingsRarely inspected, many findingsFrequently inspected, clean recordBelow median on both1.92.022.02.0010.220.430.740.9OSHA inspectionsViolations citedNEXTEEL SAHA, LLC, OSHA inspections: 2 · Violations cited: 27REMINGTON ARMS COMPA…, OSHA inspections: 2 · Violations cited: 39AGILEX FLAVORS & FRA…, OSHA inspections: 2 · Violations cited: 18REPUBLIC ENGINEERED …, OSHA inspections: 2 · Violations cited: 6NIKKISO CRYO, INC., OSHA inspections: 2 · Violations cited: 1ADVANCE PAPER BOX CO…, OSHA inspections: 2 · Violations cited: 6JUNIPER ELBOW CO., I…, OSHA inspections: 2 · Violations cited: 19MANOR TOOL AND MANUF…, OSHA inspections: 2 · Violations cited: 5MATT BREWING COMPANY…, OSHA inspections: 2 · Violations cited: 10DEBAUFRE BAKERIES INC, OSHA inspections: 2 · Violations cited: 23D. A. STEIN CULINARY…, OSHA inspections: 2 · Violations cited: 7DIAMOND SPAS, INC., OSHA inspections: 2 · Violations cited: 12SOUTHWARK METAL MANU…, OSHA inspections: 2 · Violations cited: 4CHEMIPLASTICA, INC., OSHA inspections: 2 · Violations cited: 12J.H. ROUTH PACKING C…, OSHA inspections: 2 · Violations cited: 6PACTIV CORPORATION, OSHA inspections: 2 · Violations cited: 5CENTURION INDUSTRIES…, OSHA inspections: 2 · Violations cited: 3MAC LTT STAINLESS DI…, OSHA inspections: 2 · Violations cited: 31ORNUA (WHITEHALL) IN…, OSHA inspections: 2 · Violations cited: 8FRANKLIN INTERNATION…, OSHA inspections: 2 · Violations cited: 3Halperns Steak and S…, OSHA inspections: 2 · Violations cited: 1
Halperns Steak and Seafood has 2 OSHA inspections on record and 1 violation cited. The crosshair marks the median among these Manufacturing peers. Across this sector's tracked employers, more inspections is moderately associated with more violations found -- not a coincidence, but not a guarantee either.

Halperns Steak and Seafood in the Manufacturing enforcement ledger

Among 35,243 Manufacturing employers with OSHA penalties on file, Halperns Steak and Seafood ranks #28,670 at $2,430 current penalty.

How Halperns Steak and Seafood Compares

Halperns Steak and Seafood's 0.50 violations per inspection compares to the Manufacturing sector average of 8.0 violations per employer.

Against the Manufacturing industry average of $15,763 per employer, this employer's current OSHA penalty runs well below peers (0.15x the sector average).

Enforcement detail

OSHA Inspection History

Total Inspections

2

First Inspection

2011-12-14

Last Inspection

2014-07-10

Inspection Span

3 yrs

Violations / Inspection

0.5

Avg Penalty / Inspection

$1,215

Industry Avg / Inspection

$6,093

What this shows 2 inspections over 3 years, averaging 0.5 violations per visit. That's $1,215 per inspection vs. the Manufacturing average of $6,093.

Enforcement detail

Violation Breakdown

1

Serious

100.0% of total

0

Willful

0.0% of total

0

Repeat

0.0% of total

0

Other-Than-Serious

0.0% of total

What this shows Serious violations involve hazards that could cause death or serious physical harm. Willful violations indicate intentional or knowing disregard of the law. Repeat violations are for hazards previously cited within the past 5 years.

Enforcement detail

Penalty Analysis

Initial Penalty Assessed

$4,050

Current Penalty Amount

$2,430

Penalty Reduction

40.0%

What this shows Penalties were reduced by $1,620 from the initial assessment of $4,050. Reductions may result from informal settlements, formal contests, or negotiated agreements with OSHA.

Industry Safety Context: Manufacturing

How Halperns Steak and Seafood compares to the Manufacturing sector, which has 44,645 employers tracked by PlainWorker.

Metric Halperns Steak and Seafood Industry Avg
Inspections 2 2.6
Violations 1 8.0
Total Penalty $2,430 $15,763
Avg Penalty per Inspection $1,215 $6,093
View all 44,645 employers in Manufacturing →

Nationwide Manufacturing peers with similar penalties or inspection counts

Two OSHA-record peer sets for Halperns Steak and Seafood, both outside GA so the neighborhoods are not geographic containment.

Similar current OSHA penalty

Nearest same-sector employers by current assessed penalty ($2,430 here).

Eaton Metal Products CO. LLC $2,430 UT SPS Technologies LLC $2,430 CA Transglobal LLC $2,430 MI Industrial Steel $2,430 MS

Similar OSHA inspection count

Same-sector employers with a comparable inspection history outside this state (2 inspections here).

Nexteel Saha, LLC 2 insp. Crosby, TX Remington Arms Company, LLC 2 insp. Ilion, NY Agilex Flavors & Fragrances INC 2 insp. Rancho Santa Margarita, CA Republic Engineered Products 2 insp. Canton, OH

Nearby & Similar Employers in Manufacturing

Showing 5 of 44644 other employers tracked in this sector.

Eaton Metal Products CO. LLC
Salt Lake City, UT
3 inspections $2,430
SPS Technologies LLC
Irvine, CA
2 inspections $2,430
Transglobal LLC
Auburn Hills, MI
2 inspections $2,430
Industrial Steel
Pearl, MS
2 inspections $2,430
Vip Cinema Seating
Tupelo, MS
2 inspections $2,430

Compare Halperns Steak and Seafood vs Eaton Metal Products CO. LLC side-by-side →

What to do with this record

Use Halperns Steak and Seafood's enforcement history as one data point, not the whole picture.

  • A single employer's record can look unusual in isolation. Compare Halperns Steak and Seafood against Eaton Metal Products CO. LLC, a similarly-sized employer in the same sector, before drawing conclusions. Compare side-by-side
  • See whether Halperns Steak and Seafood's inspection and penalty record is typical for Manufacturing or an outlier against the sector's own average. View the Manufacturing sector
  • Before you accept a job or raise a safety concern, search any employer for its own OSHA inspection history the same way you found this one. Search employers

Figures reflect closed OSHA and WHD federal enforcement actions on record (2010–2026); not every workplace issue results in an inspection or investigation.

Frequently Asked Questions

Is Halperns Steak and Seafood safe to work at? ▼
Based on OSHA records, Halperns Steak and Seafood's workplace safety record is relatively clean, with fewer violations than typical. The employer has 1 violations across 2 inspections, including 1 serious violations. Compared to Manufacturing industry peers, this is below average for penalties. Review the full inspection history below for details.
How many OSHA violations does Halperns Steak and Seafood have? ▼
Halperns Steak and Seafood has 1 OSHA violations on record, including 1 serious, 0 willful, and 0 repeat violations. The total current penalty amount is $2,430.
How many OSHA inspections has Halperns Steak and Seafood had? ▼
Halperns Steak and Seafood has had 2 OSHA inspections, with the first recorded on 2011-12-14 and the most recent on 2014-07-10. This averages 0.5 violations per inspection.
What is the total penalty amount for Halperns Steak and Seafood? ▼
Halperns Steak and Seafood has been assessed $2,430 in current OSHA penalties, reduced from an initial assessment of $4,050 (a 40.0% reduction).
Does Halperns Steak and Seafood have any serious or willful violations? ▼
Yes. Halperns Steak and Seafood has 1 serious violations. Serious violations involve hazards likely to cause death or serious physical harm. Willful violations indicate the employer intentionally or knowingly disregarded the law.
What industry does Halperns Steak and Seafood operate in? ▼
Halperns Steak and Seafood operates in the Manufacturing sector (NAICS code 311612). This industry has 44,645 employers tracked by PlainWorker, with 115,492 total OSHA inspections and $703.72M in cumulative penalties.
Where does Halperns Steak and Seafood rank nationally on OSHA penalties? ▼
Among the 99,447 U.S. employers with a nonzero current OSHA penalty in PlainWorker's corpus, Halperns Steak and Seafood ranks #72,865 (the lower half of penalized employers nationally). The ordinal is a live COUNT of employers with a lower total_current_penalty; see the methodology page for the exact derivation.
How does Halperns Steak and Seafood's safety record compare to industry average? ▼
Halperns Steak and Seafood's total OSHA penalty of $2,430 is below the Manufacturing industry average of $15,763 per employer. The employer has 2 inspections compared to the industry average of 2.6 per employer. For a direct comparison, Industrial Steel in Pearl, MS is a similar manufacturing employer with $2,430 in current penalties.
Data Sources & Methodology ▼

Data as of 2026. Source: U.S. Department of Labor (OSHA, WHD).

Source: OSHA Enforcement Data

Inspection and violation records from the Occupational Safety and Health Administration (OSHA), U.S. Department of Labor, covering the period 2010–2026. Includes inspection dates, violation types (serious, willful, repeat, other-than-serious), and penalty amounts. Penalties shown are current assessed amounts and may differ from original citations due to settlement, contest, or reduction.

Source: Wage and Hour Division (WHD)

Compliance actions from the WHD, covering enforcement of the Fair Labor Standards Act (FLSA), including minimum wage, overtime, and child labor violations. Back wages represent amounts owed to affected employees as determined by WHD investigations.

Employer Matching

Employers are matched across OSHA and WHD datasets by name, state, and city. Employers included in PlainWorker have 2 or more OSHA inspections or $1,000+ in WHD back wages. Data is updated monthly from data.dol.gov.

Verify with OSHA establishment search →

Every figure on PlainWorker is rendered directly from official U.S. Department of Labor OSHA and Wage & Hour Division enforcement records, no number is typed in by an editor. This employer's ratios (penalty-per-violation, industry comparisons) are computed live from the 2 inspections on record. See our editorial standards & corrections policy, the methodology behind these numbers, or report a data error. Data current as of 2026.