Manufacturing · Delair, NJ
Aluminum Shapes, LLC.
According to OSHA enforcement records (2010–2026), Aluminum Shapes, LLC. ranks #50 of 99,447 penalized U.S. employers by total current penalty, with a concerning safety record: 170 violations across 13 inspections.
- $663,312
- OSHA penalties
- 170
- Violations cited
- 13
- OSHA inspections
- #50
- of 99,447 penalized employers
Aluminum Shapes, LLC. in Delair, NJ has been the subject of 13 OSHA workplace inspections and 170 citations since 2010, according to enforcement records from the U.S. Department of Labor. Total penalties assessed: $663,312. All enforcement data below is sourced from the DOL public enforcement databases at data.dol.gov.
The record in one line
OSHA has inspected Aluminum Shapes, LLC. 13 times over 8 years, roughly annually. These inspections turned up 170 violations, averaging 13.1 per inspection - an extremely dense concentration of citations. According to OSHA enforcement records, its total current penalty ranks #50 of 99,447 penalized U.S. employers (the top 1% of penalized employers nationally). Of these, 116 were classified as serious and 17 as willful - indicating hazards that could cause death or serious harm. Against the Manufacturing industry average of 3 inspections per employer, this runs far above peers (5.0x the sector average) on inspection frequency. For comparison, Tesla, INC. in Fremont, CA is another manufacturing employer with 59 OSHA inspections on record and $661,780 in current penalties.
- 13.1
- violations per inspection
- 68.2%
- of violations were serious
- #50
- of 99,447 penalized employers
Compliance score
- F OSHA safety compliance: 170 violations across 13 OSHA inspections (13.1 per inspection), vs. national p10 0.0 (best) / p90 5.5 (worst) among 145,626 inspected employers.
Channels are separate federal datasets: a dimension marked not applicable simply has no record in that dataset for this employer, not a good or bad score.
How Aluminum Shapes, LLC. compares on OSHA penalties
Total current penalty vs the Manufacturing per-employer average
- Aluminum Shapes, LLC.
Aluminum Shapes, LLC.
$663,312 in penalties
- Manufacturing avg $15,763
Manufacturing industry average (per employer)
$15,763 in penalties
What this shows Aluminum Shapes, LLC. runs far above peers (42.1x the sector average) in total OSHA penalties.
Where this penalty ranks nationally
Total current OSHA penalty vs every U.S. employer with a nonzero penalty
$663,312 Bottom 1% least affordable more affordable than 0% of 99,447 U.S. employers with a penalty
Each bar is a $5K-wide band; taller bars hold more U.S. employers with a penalty. The dashed line + filled bar mark this entry. Hover or tap any bar for its full count, share, and where it sits relative to this entry.
Source U.S. Department of Labor, OSHA enforcement extracts · 2026
Does more inspection scrutiny mean more findings?
Each dot is one of 21 Manufacturing employers with an OSHA inspection on record, placed by inspections and violations cited. The highlighted dot is Aluminum Shapes, LLC..
Aluminum Shapes, LLC. in the Manufacturing enforcement ledger
In Manufacturing, Aluminum Shapes, LLC. sits at penalty rank #32 of 35,243 penalized establishments ($663,312 assessed).
How Aluminum Shapes, LLC. Compares
Aluminum Shapes, LLC.'s 13.08 violations per inspection compares to the Manufacturing sector average of 8.0 violations per employer.
Against the Manufacturing industry average of $15,763 per employer, this employer's current OSHA penalty runs far above peers (42.1x the sector average).
Enforcement detail
OSHA Inspection History
Total Inspections
13
First Inspection
2011-11-21
Last Inspection
2019-08-02
Inspection Span
8 yrs
Violations / Inspection
13.1
Avg Penalty / Inspection
$51,024
Industry Avg / Inspection
$6,093
What this shows 13 inspections over 8 years, averaging 13.1 violations per visit. That's $51,024 per inspection vs. the Manufacturing average of $6,093.
Enforcement detail
Violation Breakdown
116
Serious
68.2% of total
17
Willful
10.0% of total
28
Repeat
16.5% of total
9
Other-Than-Serious
5.3% of total
What this shows Serious violations involve hazards that could cause death or serious physical harm. Willful violations indicate intentional or knowing disregard of the law. Repeat violations are for hazards previously cited within the past 5 years.
Enforcement detail
Penalty Analysis
Initial Penalty Assessed
$2.42M
Current Penalty Amount
$663,312
Penalty Reduction
72.6%
What this shows Penalties were reduced by $1.75M from the initial assessment of $2.42M. Reductions may result from informal settlements, formal contests, or negotiated agreements with OSHA.
Industry Safety Context: Manufacturing
How Aluminum Shapes, LLC. compares to the Manufacturing sector, which has 44,645 employers tracked by PlainWorker.
| Metric | Aluminum Shapes, LLC. | Industry Avg |
|---|---|---|
| Inspections | 13 | 2.6 |
| Violations | 170 | 8.0 |
| Total Penalty | $663,312 | $15,763 |
| Avg Penalty per Inspection | $51,024 | $6,093 |
Nationwide Manufacturing peers with similar penalties or inspection counts
Two OSHA-record peer sets for Aluminum Shapes, LLC., both outside NJ so the neighborhoods are not geographic containment.
Similar current OSHA penalty
Nearest same-sector employers by current assessed penalty ($663,312 here).
Similar OSHA inspection count
Same-sector employers with a comparable inspection history outside this state (13 inspections here).
Nearby & Similar Employers in Manufacturing
Showing 5 of 44644 other employers tracked in this sector.
Compare Aluminum Shapes, LLC. vs Smithfield Foods North side-by-side →
What to do with this record
Use Aluminum Shapes, LLC.'s enforcement history as one data point, not the whole picture.
- A single employer's record can look unusual in isolation. Compare Aluminum Shapes, LLC. against Smithfield Foods North, a similarly-sized employer in the same sector, before drawing conclusions. Compare side-by-side
- See whether Aluminum Shapes, LLC.'s inspection and penalty record is typical for Manufacturing or an outlier against the sector's own average. View the Manufacturing sector
- Before you accept a job or raise a safety concern, search any employer for its own OSHA inspection history the same way you found this one. Search employers
Figures reflect closed OSHA and WHD federal enforcement actions on record (2010–2026); not every workplace issue results in an inspection or investigation.
Frequently Asked Questions
Is Aluminum Shapes, LLC. safe to work at? ▼
How many OSHA violations does Aluminum Shapes, LLC. have? ▼
How many OSHA inspections has Aluminum Shapes, LLC. had? ▼
What is the total penalty amount for Aluminum Shapes, LLC.? ▼
Does Aluminum Shapes, LLC. have any serious or willful violations? ▼
What industry does Aluminum Shapes, LLC. operate in? ▼
Where does Aluminum Shapes, LLC. rank nationally on OSHA penalties? ▼
How does Aluminum Shapes, LLC.'s safety record compare to industry average? ▼
Data Sources & Methodology ▼
Data as of 2026. Source: U.S. Department of Labor (OSHA, WHD).
Source: OSHA Enforcement Data
Inspection and violation records from the Occupational Safety and Health Administration (OSHA), U.S. Department of Labor, covering the period 2010–2026. Includes inspection dates, violation types (serious, willful, repeat, other-than-serious), and penalty amounts. Penalties shown are current assessed amounts and may differ from original citations due to settlement, contest, or reduction.
Source: Wage and Hour Division (WHD)
Compliance actions from the WHD, covering enforcement of the Fair Labor Standards Act (FLSA), including minimum wage, overtime, and child labor violations. Back wages represent amounts owed to affected employees as determined by WHD investigations.
Employer Matching
Employers are matched across OSHA and WHD datasets by name, state, and city. Employers included in PlainWorker have 2 or more OSHA inspections or $1,000+ in WHD back wages. Data is updated monthly from data.dol.gov.