Manufacturing · Adrian, MI
Adrian Tool Corporation
According to OSHA enforcement records (2010–2026), Adrian Tool Corporation ranks #67,442 of 99,447 penalized U.S. employers by total current penalty, with a mixed safety record: 12 violations across 4 inspections.
- $3,100
- OSHA penalties
- 12
- Violations cited
- 4
- OSHA inspections
- #67,442
- of 99,447 penalized employers
Adrian Tool Corporation in Adrian, MI has been the subject of 4 OSHA workplace inspections and 12 citations since 2010, according to enforcement records from the U.S. Department of Labor. Total penalties assessed: $3,100. All enforcement data below is sourced from the DOL public enforcement databases at data.dol.gov.
The record in one line
OSHA has inspected Adrian Tool Corporation 4 times over 3 years, roughly annually. These inspections resulted in 12 violations, averaging 3.0 per inspection, above what's typical for a single visit. According to OSHA enforcement records, its total current penalty ranks #67,442 of 99,447 penalized U.S. employers (the lower half of penalized employers nationally). Of these, 10 were classified as serious - indicating hazards that could cause death or serious harm. Against the Manufacturing industry average of 3 inspections per employer, this runs moderately above peers (1.5x the sector average) on inspection frequency. For comparison, DLD Express. in Santa Ana, CA is another manufacturing employer with 0 OSHA inspections on record and $0 in current penalties.
- 3.0
- violations per inspection
- 83.3%
- of violations were serious
- #67,442
- of 99,447 penalized employers
Compliance score
- F OSHA safety compliance: 12 violations across 4 OSHA inspections (3.0 per inspection), vs. national p10 0.0 (best) / p90 5.5 (worst) among 145,626 inspected employers.
Channels are separate federal datasets: a dimension marked not applicable simply has no record in that dataset for this employer, not a good or bad score.
How Adrian Tool Corporation compares on OSHA penalties
Total current penalty vs the Manufacturing per-employer average
- Adrian Tool Corporation $3,100
Adrian Tool Corporation
$3,100 in penalties
- Manufacturing avg
Manufacturing industry average (per employer)
$15,763 in penalties
What this shows Adrian Tool Corporation runs well below peers (0.20x the sector average) in total OSHA penalties.
Where this penalty ranks nationally
Total current OSHA penalty vs every U.S. employer with a nonzero penalty
$3,100 Top 32% most affordable more affordable than 68% of 99,447 U.S. employers with a penalty
Each bar is a $5K-wide band; taller bars hold more U.S. employers with a penalty. The dashed line + filled bar mark this entry. Hover or tap any bar for its full count, share, and where it sits relative to this entry.
Source U.S. Department of Labor, OSHA enforcement extracts · 2026
Does more inspection scrutiny mean more findings?
Each dot is one of 21 Manufacturing employers with an OSHA inspection on record, placed by inspections and violations cited. The highlighted dot is Adrian Tool Corporation.
Adrian Tool Corporation in the Manufacturing enforcement ledger
In Manufacturing, Adrian Tool Corporation sits at penalty rank #27,044 of 35,243 penalized establishments ($3,100 assessed).
How Adrian Tool Corporation Compares
Adrian Tool Corporation's 3.00 violations per inspection compares to the Manufacturing sector average of 8.0 violations per employer.
Against the Manufacturing industry average of $15,763 per employer, this employer's current OSHA penalty runs well below peers (0.20x the sector average).
Enforcement detail
OSHA Inspection History
Total Inspections
4
First Inspection
2017-11-27
Last Inspection
2020-10-30
Inspection Span
3 yrs
Violations / Inspection
3.0
Avg Penalty / Inspection
$775
Industry Avg / Inspection
$6,093
What this shows 4 inspections over 3 years, averaging 3.0 violations per visit. That's $775 per inspection vs. the Manufacturing average of $6,093.
Enforcement detail
Violation Breakdown
10
Serious
83.3% of total
0
Willful
0.0% of total
0
Repeat
0.0% of total
2
Other-Than-Serious
16.7% of total
What this shows Serious violations involve hazards that could cause death or serious physical harm. Willful violations indicate intentional or knowing disregard of the law. Repeat violations are for hazards previously cited within the past 5 years.
Enforcement detail
Penalty Analysis
Initial Penalty Assessed
$4,400
Current Penalty Amount
$3,100
Penalty Reduction
29.5%
What this shows Penalties were reduced by $1,300 from the initial assessment of $4,400. Reductions may result from informal settlements, formal contests, or negotiated agreements with OSHA.
Industry Safety Context: Manufacturing
How Adrian Tool Corporation compares to the Manufacturing sector, which has 44,645 employers tracked by PlainWorker.
| Metric | Adrian Tool Corporation | Industry Avg |
|---|---|---|
| Inspections | 4 | 2.6 |
| Violations | 12 | 8.0 |
| Total Penalty | $3,100 | $15,763 |
| Avg Penalty per Inspection | $775 | $6,093 |
Nationwide Manufacturing peers with similar penalties or inspection counts
Two OSHA-record peer sets for Adrian Tool Corporation, both outside MI so the neighborhoods are not geographic containment.
Similar current OSHA penalty
Nearest same-sector employers by current assessed penalty ($3,100 here).
Similar OSHA inspection count
Same-sector employers with a comparable inspection history outside this state (4 inspections here).
Nearby & Similar Employers in Manufacturing
Showing 5 of 44644 other employers tracked in this sector.
Compare Adrian Tool Corporation vs Regal Cut Stone LLC side-by-side →
What to do with this record
Use Adrian Tool Corporation's enforcement history as one data point, not the whole picture.
- A single employer's record can look unusual in isolation. Compare Adrian Tool Corporation against Regal Cut Stone LLC, a similarly-sized employer in the same sector, before drawing conclusions. Compare side-by-side
- See whether Adrian Tool Corporation's inspection and penalty record is typical for Manufacturing or an outlier against the sector's own average. View the Manufacturing sector
- Before you accept a job or raise a safety concern, search any employer for its own OSHA inspection history the same way you found this one. Search employers
Figures reflect closed OSHA and WHD federal enforcement actions on record (2010–2026); not every workplace issue results in an inspection or investigation.
Frequently Asked Questions
Is Adrian Tool Corporation safe to work at? ▼
How many OSHA violations does Adrian Tool Corporation have? ▼
How many OSHA inspections has Adrian Tool Corporation had? ▼
What is the total penalty amount for Adrian Tool Corporation? ▼
Does Adrian Tool Corporation have any serious or willful violations? ▼
What industry does Adrian Tool Corporation operate in? ▼
Where does Adrian Tool Corporation rank nationally on OSHA penalties? ▼
How does Adrian Tool Corporation's safety record compare to industry average? ▼
Data Sources & Methodology ▼
Data as of 2026. Source: U.S. Department of Labor (OSHA, WHD).
Source: OSHA Enforcement Data
Inspection and violation records from the Occupational Safety and Health Administration (OSHA), U.S. Department of Labor, covering the period 2010–2026. Includes inspection dates, violation types (serious, willful, repeat, other-than-serious), and penalty amounts. Penalties shown are current assessed amounts and may differ from original citations due to settlement, contest, or reduction.
Source: Wage and Hour Division (WHD)
Compliance actions from the WHD, covering enforcement of the Fair Labor Standards Act (FLSA), including minimum wage, overtime, and child labor violations. Back wages represent amounts owed to affected employees as determined by WHD investigations.
Employer Matching
Employers are matched across OSHA and WHD datasets by name, state, and city. Employers included in PlainWorker have 2 or more OSHA inspections or $1,000+ in WHD back wages. Data is updated monthly from data.dol.gov.